Elegir Idioma:
Buscar: 
   
1
Post Solder - C/S (Silver) & G/D (Gold) - LOW TEMPERATURE BRAZING SOLDER


For use on non-ferrous and ferrous metals


  • Consistente de alta resistencia
  • Baja temperatura de unión
  • No tóxico, no contiene plomo o cadmio
  • Enfriar para que coincida con el color cromo-plata
  • Se adherirá a preciosos cromo-cobalto, níquel y muchos otros metales


ProTech C/S es un 85% de plata, de baja temperatura de construcción y reparación de material que le dará los resultados de calidad profesional cuando se usa de acuerdo a los siguientes procedimientos:

Asegúrese de usar una cantidad suficiente de material para llenar completamente la unión.
Guarde la jeringa en un lugar fresco cuando no se use.
No refrigerar.
Si la jeringa no se ha utilizado durante un tiempo, hágala rodar por un minuto sobre una plataforma vibrante para agitar el contenido.


C/S SOLDER # DE ARTÍCULO PRECIO
28g. CSS1 $126.95
3x28g. CSS3 $333.95

G/D SOLDER # DE ARTÍCULO PRECIO
28g. GDS1 $127.95
3x28g. GDS3 $339.95





   Imprimir
C/S & G/D SDS

   Imprimir
Ver IU

   Imprimir
Ver IU


APLICACIÓN DE LA LÁMPARA PARA SOLDAR
La lámpara para soldar debe ser capaz de producir de 704.44 a 760oC.

Make sure that the joint is clean and free of contaminants. We suggest rubber wheeling the joint as a final cleaning step. Apply pressure to plunger until desired amount of material has been deposited in the joint. To stop the material from existing the syringe, gently pull back on the plunger. Using a "neutral" flame, heat both sides of joint back and forth, as evenly as possible. Do not heat the solder directly! When solder reaches 1250° F, it will flow. Then remove heat. Allow part to cool slowly. Replace cap.


RESISTANCE MACHINE APPLICATION
Make sure that the joint is clean and free of contaminants. We suggest rubber wheeling the joint as a final cleaning step. Remove the cap from the syringe. Apply pressure to the plunger until the desired amount of material has been deposited in the joint. To stop the material from exiting the syringe, gently pull back on the plunger. Adjust machine to produce 1350° F to 1400° F. (Second setting on most machines.) Moisten the electrodes with water. Place the carbon tip on the side of the solder. Place metal tip ground wire from the machine to the base of the metal, approximately 10 mm away from the carbon tip.
Cuando la soldadura fluya (a 676.67 °C), corra suavemente la punta de carbono a través de la soldadura, usando la suficiente presión para asegurar un circuito completo. Permita que la soldadura se enfríe lentamente. Reemplace la tapa a la jeringa.

APLICACIÓN DEL HORNO: WITH PROTECTED ATMOSPHERE
Preheat oven to 1250° F. Make sure that the joint is clean and free of contaminants. Remove the cap from the syringe. Apply pressure to plunger until desired amount of material has been deposited into the joint. To stop the material from exiting the syringe, gently pull back on the plunger. Place appliance into the furnace. When solder flows discontinue heating. Allow appliance to cool slowly (adjust belt speed according to size of appliance). Replace cap on syringe.

WITHOUT PROTECTED ATMOSPHERE
Preheat appliance in oven to 1300° F. Remove heated appliance from furnace. Make sure that the joint is clean and free of contaminants. Allow appliance to cool to approximately 1150° F. Remove cap from ProTech C/S syringe. Apply pressure to plunger until desired amount of material has been deposited into the joint. To stop the material from exiting the syringe, gently pull back on the plunger. Place appliance back into furnace. Slowly increase the furnace temperature to 1300° F. When solder flows, discontinue heating. Allow appliance to cool slowly. Replace cap onto syringe.

CARACTERÍSTICAS: NO TÓXICO
Libre de cadmio para el uso seguro intra-oral.

WIDE PLASTIC MELTING RANGE
Suited for lap, tee, and butt joints.

ALTA RESISTENCIA
Fuerza de tensión: 86,000 psi
Temperatura de unión: 676.67 - 704.44 °C
Color de Depósito: Cromo-Plata

NON-TARNISHING
Since ProTech C/S contains only precious metals (no zinc, nickel, lead, etc.) binders and flux, there is no tarnishing.

WILL NOT TURN PORCELAIN GREEN
The greening of porcelain is caused by an excessive use of silver solder to create a strong joint. With a high tensile strength of 86,000 psi, only a small amount of ProTech? C/S is required to get professional results. The needle nosed syringe allows you strict control over the amount used. Should a particular application require a smaller deposit of material from the syringe, the plastic nose can be removed and replaced with a stainless steel adapter and stainless steel hypodermic needles (14 - 18 gauge).

1